ACI Structural Journal January/February 2016
Newswise — We often prefer the simplest solution for better quality control. In this aspect, precast concrete (PC) offers one of the most straightforward and speedy methods for the construction of multi-story buildings that require minimal maintenance. In high seismic regions such as California, seismic risk issues are always raised, and PC structures should demonstrate their ability to provide structural integrity between the connected precast members under maximum credible earthquake.
Lateral load resistance of precast concrete (PC) walls is achieved by emulating cast-in-place detailing, by the use of grout sleeve splices for longitudinal reinforcement, by adopting the post-tensioning technique, and/or by mechanical connection with the roof and floor diaphragms. An innovative steel plate connector system developed by Seoul National University’s research team in Korea for connection between precast concrete (PC) wall panels or to foundation may not need any of the above methods. Even the non-shrink grout, which is necessary when applying the post-tensioning or re-bar splicing technique, is not needed for this steel plate connector system (though you can apply the grout after bolting for fire and corrosion protection and to fill the gap).
Such a connector system is expected to enhance constructability and lateral load resistance, and is perfect for fast-track low-rise buildings such as tilt-up construction in low to high seismic areas. The system consists of two bolt type C-shaped connectors, end-threaded reinforcing bars, hexagonal nuts and washers/shims. Details of the bolt type connectors are shown in Figs. 1 to 3. “Two pieces of the C-shaped connectors with horizontal and vertical slots would provide a great tolerance for construction variations,” said Sung-Gul Hong, a professor of Seoul National University. “Even though this system has never been applied in the real world, we believe that the developed system would increase construction efficiency enormously without sacrificing its lateral load resistance capability,” said Hong.
The C-shaped connectors are intended to transfer tension and compression forces in the main flexural reinforcement and/or concrete. The maximum stress concentration is at the interface between two steel plates as the force path changes direction. The details at this critical location might be something to be fine-tuned before its application. The hollow part at the end of the wall is essential for easy assembly of PC panels by bolting. There are two options here: each panel element can be pre-tensioned, or the panels can be produced without a prestressing process.
According to Thomas Kang, a professor of Seoul National University, “the presence of shear key is a key to effective shear transfer of lateral forces between the wall panels and between the wall panel and foundation, making a pure dry precast concrete option available.” To verify the seismic robustness of the developed pure dry connection, experimental research in the Department of Architecture & Architectural Engineering at Seoul National University has been conducted. The size and thickness of the C-shaped steel plate connectors were determined such that the plate would not yield prior to yielding of flexural re-bars in the wall. Also, buckling strength of each steel plate was checked in the design phase. “The fact that system’s seismic performance has been verified is very important and will make it easier for engineers to understand the power of this system,” said Kang convincingly. “We used cast-in-place joints for horizontal connection between flange and web elements of T-walls, but we think that this can also be replaced by the steel plate connectors. Two C-shaped connectors can be potentially combined into a single box-shaped connector, if properly designed.”
The research can be found in a paper titled “Cyclic Lateral Testing of Precast Concrete T-Walls in Fast Low-Rise Construction”, published by ACI Structural Journal.
For more information, contact:
Julie Webb
Marketing Communications Specialist
248-848-3148
[email protected]
Always Advancing – The American Concrete Institute is a leading authority and resource worldwide for the development and distribution of consensus-based standards and technical resources, educational programs and certifications for individuals and organizations involved in concrete design, construction and materials, who share a commitment to pursuing the best use of concrete. ACI’s inclusive, individual member-driven structure and valuable, cost-effective benefits result in an essential organization that invites partnerships and welcomes all concrete professionals who wish to be a part of a respected, connected social group that provides an opportunity for professional growth, networking and enjoyment. For additional information, visit www.concrete.org.
RSS